• Control safety during construction and permanently remind contractors to respect safety procedures. Supervisors also have full authority to suspend works in case safety regulations are not observed. • Get good knowledge of all the construction specifications procedures and schedules. • QAQC oriented, able to follow both construction/precoma and quality processes and standard • Must have knowledge and understanding of the piping phase of prefabrication and construction operations at the jobsite • Report to the AGI CONSTRUCTION SITE LEAD any difficulties that might prevent the construction targets being achieved (lack of drawings, specifications or material, interference by other contractors, incongruence in the plans and schedules, environmental/social problems particularly in the work areas, etc.) • Supervise the activities of the contractor by checking the availability and maintenance status of construction equipment and also the correct use of equipment and manpower. • Give technical support to contractor with the aim of facilitating the quick and economical execution of the works. • Give the contractor all the explanations needed for a correct interpretation of the engineering documents. • Verify that the works are performed with the required quality level and that the contractors are performing quality controls as required. • Before any new construction activity begins, make personally sure that everything needed for the proper performance of that activity is actually available on site (i.e. availability of materials, manpower and equipment, electrical power and absence of any kind of impediment) and report any deficiencies or impediments to the AGI CONSTRUCTION SITE LEAD. • Monitor the implementation of all works as per good engineering and construction practice. • Keep in closed contact with the AGI CONSTRUCTION SITE LEAD, Field Engineer and the Site Quality management Organisation in order to supply them all the information needed for proper planning of quality control and document. Collaborate with them when revising and updating construction schedules. • Verify that the works proceed in conformity with the construction schedule, and report any deviation to the AGI CONSTRUCTION SITE LEAD. • Supervise mechanical completion and plant turn-over and make sure that the “punch-lists works” are performed correctly and rapidly. • Review validity of any contractors extra works request and pay particular attention to the supervision of the relevant activities. • To ensure compliance with the applicable codes, practices, policies, performance standards, and specifications such and not limited to ASME, ASTM, ANSI, API, NEMA . • Assist QS for measure the physical progress of the works in charge on a daily/weekly basis for progress report issue. • Make sure that the contractor submits his daily reports regarding equipment and manpower and carefully check that information are correct and comply with the agreed procedures. • Proactively undertake and promote the use of behavioral and incentivised HSE work programmes, and campaigns. • Ensure all quality control checks and tests are instigated, with records maintained and available as required for underground and above ground GRE/HDPE/CS/SS, hydrostatic testing, flushing and drying, safety relief valve installation, all in accordance with contractors’ agreed ITP, method statements and project specifications • Ensure contractors follow approved procedures, plans and method statements • Ensure the most current design documents are used to complete the work and that all design changes are approved prior to implementation • Ensure that all construction milestone dates are completed as scheduled • Ensure that all construction activities meet quality and workmanship standards • Ensure required permits are in place prior to the start of the work at site • Prepare reports and forecasts, including summary of construction progress • Coordinates activities with other disciplines or areas, as instructed by project management

• Bachelor’s degree/diploma in Mechanical, CSWIP 3.1 Welding Inspector and NDT Level 2 Certification. • Experience Required • 10 years large scale project experience in mechanical, structural and piping installation. • Required Competencies • Conversant with all NDTs technics. • Fully aware and experienced of all applicable codes, policies, standards, and best practices used in the Oil and Gas Industry. • Good interpersonal and communication and motivational skills, team player, the ability to work with multiple discipline and in a multicultural environment. • Fully conversant in English (speaking and with excellent writing skill). • Excellent computer literacy and knowledge of design and visualisation software. • Demonstrate project management and supervision skills. • Excellent organisational, time management, leadership, and decision-making skills. • Working knowledge of applicable codes and standards (ASME, ASTM, ANSI, API, NEMA). • Prefer experience on large scope. • Minimum 10 years’ experience in large scale project in mechanical, structural and piping installation, including large/small bore, piping systems and instrument supports, equipment setting, steel structure fabrication and erection. • All candidates who meet the criteria outlined above are encouraged to apply under the job vacancy “QSSU-EACOP-APS- AGI PIPING SPECIALIST”